焊烟除尘设备在日产的运用中需求我们进行日常的保护，这样才能确保设备正常的运转。下面就带大家了解下焊烟除尘设备日常保护的几个关键。

The application of welding smoke and dust removal equipment in Nissan requires us to carry out daily protection in order to ensure the normal operation of the equipment. Below, we will take you to understand several key daily protection measures for welding smoke and dust removal equipment.

　　1、管理人员应熟悉除尘器的原理、性能、运用条件，并掌握调整和修理办法。

1. Management personnel should be familiar with the principle, performance, and operating conditions of dust collectors, and master adjustment and repair methods.

　　2、定期测定工艺参数，如烟气量、温度、浓度等，发现异常，应查找原因并及时处理。

2. Regularly measure process parameters such as smoke volume, temperature, concentration, etc. If abnormalities are found, the cause should be identified and promptly addressed.

　　3、减速机、输灰设备等机械运动部件应按规定注油和换油，发现有不正常现象应及时排除。

3. Mechanical moving parts such as reducers and ash conveying equipment should be lubricated and replaced according to regulations. Any abnormal phenomena should be promptly eliminated.

　　4、电磁脉冲阀如发生毛病，应及时地排除，如内部有杂质、水分，应进行清理，如膜片损坏应及时 换。

4. If the electromagnetic pulse valve malfunctions, it should be promptly eliminated. If there are impurities or moisture inside, it should be cleaned. If the diaphragm is damaged, it should be replaced in a timely manner.

　　5、停机时，不用堵截紧缩气源，尤其在风机作业时， 向提高阀气缸供给紧缩空气，以确保提高阀处开启状况。

5. When shutting down, there is no need to block the compressed air source, especially during fan operation, to supply compressed air to the lifting valve cylinder to ensure the opening status of the lifting valve.

　　6、除尘器在正常作业时，排灰设备不能停止作业，否则，灰斗内很快会积满粉尘致使溢入袋室，迫使除尘器停止作业。

6. When the dust collector is operating normally, the ash discharge equipment cannot stop working. Otherwise, the ash hopper will quickly accumulate dust and overflow into the bag room, forcing the dust collector to stop working.

　　7、开机时，应先接通紧缩空气至储气罐，接通操控电源，发动排灰设备，假如体系中还有其它设备，应先发动下游设备。

7. When starting up, the compressed air should be connected to the air storage tank, the control power should be turned on, and the ash discharge equipment should be started. If there are other equipment in the system, the downstream equipment should be started first.

　　8、储气罐、气源三联件中的油水分离器应每班排污一次，一起油水分离器应每隔3～6月清洗一次，油雾器应常常查看存油状况，及时加油。

8. The oil-water separator in the gas storage tank and gas source triple unit should be discharged once per shift, and the oil-water separator should be cleaned every 3-6 months. The oil mist collector should regularly check the oil storage status and add oil in a timely manner.

　　9、运用定时式清灰操控柜，应定期测定清灰周期是否准确，否则应进行调整。运用定阻式脉冲操控仪，应定期查看压力开关的作业状况，测压口是否堵塞，并进行清理。

9. When using a timed ash cleaning control cabinet, the accuracy of the ash cleaning cycle should be regularly measured, otherwise adjustments should be made. When using a fixed resistance pulse controller, it is necessary to regularly check the operation status of the pressure switch, check if the pressure measuring port is blocked, and clean it.

　　10、停机时，在工艺体系停止之后，应保持除尘器和排风机持续作业一段时间，以除尘设备内的潮气和粉尘， 注意的是，在除尘器停止作业时， 反复对除尘器进行清灰(可用手动清灰)，将除尘滤袋上的粉尘除掉，以访受潮气影响而糊袋子。

10. When shutting down, after the process system stops, the dust collector and exhaust fan should be kept operating continuously for a period of time to remove moisture and dust from the dust removal equipment. It is important to repeatedly clean the dust collector (manual cleaning can be used) when the dust collector stops working, remove the dust from the dust filter bag, and prevent the bag from being affected by moisture and sticking.

以上就是有关：多工位焊烟除尘设备 的介绍，想了解更多的内容请点击：http://www.sdcjtz.com 我们将会全心全意为您提供满分服务，欢迎您的来电！

The above is an introduction to multi station welding smoke and dust removal equipment. To learn more, please click: http://www.sdcjtz.com We will wholeheartedly provide you with full score service. Welcome to call us!

上一篇：自动式抛丸机的工作原理
下一篇：VOCs废气处理设备的使用寿命