工业涂装流水线很难确保工件的喷涂作用，存在许多不可控的要素，即便在日常运作进程中十分重视工业涂装流水线的保护保养和质量规则，可是有些时分仍是没有到达预期的抱负要求。那麼，工业涂装流水线该怎样做才干确保工件的涂质量呢?以下几点告知你!

　　It is difficult to ensure the spraying effect of workpieces in industrial coating assembly lines, and there are many uncontrollable factors. Even though the protection, maintenance, and quality rules of industrial coating assembly lines are highly valued in daily operation, sometimes they still fail to meet the expected expectations. So, how can an industrial coating assembly line ensure the coating quality of workpieces? Here are a few things to tell you!

　　选择合适自己产品的前处理工艺，可以显着进步镀层的特性和充分发挥镀层的成效。假设喷涂前处理只展开除油，可以考虑一般的加工工艺规则。假设有转化膜的存有，可以进一步进步镀层特性和添加镀层使用期，做到得不偿失的实际作用。酸洗磷化为底材出示了一个不但滑面?，给镀层以十分好的咬力，进一步进步了粘合力，使实镀层特性足以现。要書的是磷化处理膜的存有可以過止镀层的膜下浸蚀，确保镀层损書后，浸蚀不简单大规模发生，以致生锈破孔，原因取决于磷化处理膜出示的均一表层，能技捺部分原电池原理的发生。

　　Choosing a suitable pre-treatment process for one's own product can significantly improve the characteristics of the coating and fully utilize its effectiveness. Assuming that the pre-treatment before spraying only involves oil removal, general processing rules can be considered. Assuming the existence of a conversion film, it can further improve the characteristics of the coating and add coating service life, achieving a practical effect that is not worth the loss. Acid pickling and phosphating provide a smooth surface for the substrate?, By providing excellent biting force to the coating, the adhesion is further improved, making the characteristics of the actual coating sufficient. What needs to be studied is the ability of the phosphating treatment film to prevent the corrosion under the coating, ensuring that after the coating is damaged, the corrosion does not occur on a large scale, resulting in rust and perforation. The reason depends on the uniform surface layer of the phosphating treatment film, which can inhibit the occurrence of some primary battery principles.

　　尘埃是喷涂质量的敌人，简单发生涂面颗粒，为改进颗粒缺点，喷涂车间在喷枪过滤器的频率从两周一次进步到一周一次，假设滤芯此前是用溶剂枪清洗，可以改用溶剂浸泡，分化滤芯上附着的涂料凝聚物，再用溶剂枪清洗。

　　Dust is the enemy of spray quality, and coating particles can easily occur. To improve the shortcomings of particles, the frequency of the spray gun filter in the spray workshop has increased from once every two weeks to once a week. Assuming that the filter element was previously cleaned with a solvent gun, it can be soaked in a solvent to differentiate the coating agglomerates attached to the filter element, and then cleaned with a solvent gun.

　　喷涂加工进程中，要留心工业涂装流水线是架运送链条是不是出现异常。若有出现异常，当即采纳保护办法，未雨绸缪，确保加工进程一切正常运作。别的，别忘记查看悬挂链的损坏状况。假设有不一样水平的损坏，要多加心。

　　During the spraying process, it is important to pay attention to whether there are any abnormalities in the transportation chain of the industrial coating assembly line. If there are any abnormalities, immediately adopt protective measures, take precautions, and ensure the normal operation of the processing process. Also, don't forget to check the damage status of the suspension chain. Assuming there is varying levels of damage, extra care should be taken.

　　在工业涂装流水线机器设备的维修保养中，准时观查全自动喷涂往复机传动轮和普攻轮是不是有出现异常凹凸不平，并置心中后期是不是有出现异常的纹理和刮痕，是不是有明显的不平。除此之外，机器设备可否一切正常工作中，喷雾器是不是匀称都是很重要的。

　　In the maintenance and upkeep of industrial coating assembly line machinery and equipment, timely observe whether there are any abnormal unevenness in the transmission wheel and common tapping wheel of the fully automatic spraying reciprocating machine, and check whether there are any abnormal textures and scratches in the later stage, and whether there are obvious unevenness. In addition, it is very important that whether the machinery and equipment can work normally and whether the spray is symmetrical.

　　由于涂装流水线选用的喷漆产品要害成份是有机溶剂，有机溶剂的捷蒸腾，十分简单形成环境温度骡峰，水解结，因此可以根据時漆丅艺的不一样，处理喷漆全进程中喷漆不勾称的状况。为了防止相似状况的发生，喷涂加工选用粉未状和配套设备油漆稀释剂，可是要防止水进入，否则会导致不良影响。

　　Due to the use of organic solvents as the key component of the spray paint products in the painting assembly line, the rapid evaporation of organic solvents can easily form environmental temperature peaks and hydrolysis bonds. Therefore, it is possible to handle the situation of uneven spray paint throughout the entire painting process according to the different painting techniques. In order to prevent similar situations from occurring, powder and matching equipment paint diluents are selected for spray coating processing. However, water should be prevented from entering, otherwise it may cause adverse effects.

　　喷漆前留心标准气压管道油气别蛮器，并将别离设备底端的水道除整齐。假设由于有机溶剂蒸发快、相对湿度大而形成喷季器不匀称，应尽可能用怡当的防潮剂代替油漆样释剂，以削减蒸发速率，防止喷雾器不匀称。

　　Before painting, pay attention to the standard air pressure pipeline oil and gas pressure sensor, and clean the water channel away from the bottom of the equipment neatly. Assuming that the organic solvent evaporates quickly and the relative humidity is high, which causes the asymmetry of the sprayer, it is necessary to replace the paint sample release agent with an appropriate moisture-proof agent as far as possible to reduce the evaporation rate and prevent the asymmetry of the spray.

　　本文由 工业涂装流水线 友情奉献.更多有关的知识请点击  http://www.sdcjtz.com    真诚的态度.为您提供为全面的服务.更多有关的知识我们将

　　This article is a friendly contribution from the industrial coating assembly line. For more related knowledge, please click http://www.sdcjtz.com Sincere attitude. We will provide you with comprehensive service. With more relevant knowledge, we will

上一篇：涂装行业废气治理：沸石转轮催化燃烧设备
下一篇：购买自动抛丸机时要注意的几个因素