涂装流水线可作为运输机械使用，已广泛应用于煤炭、粮食、面粉加工厂等行业。可输送散装物料和袋装物料。用户在安装和使用此类设备时，对于导致故障的一些原因并不清楚，也没有太多的处理方法。

The painting assembly line can be used as a transportation machinery and has been widely used in industries such as coal, grain, and flour processing plants. Can transport bulk materials and bagged materials. When users install and use such devices, they are not clear about some of the causes of malfunctions and do not have many solutions.

在涂装流水线生产的操作中，打滑的常见原因和解决方法有很多。

There are many common causes and solutions for slippage in the production of painting assembly lines.

1.初张力太小。生产线离开滚筒的地方不够紧，导致生产线下降。这种情况通常发生在启动时。解决方法是调整张紧装置，增加初张力。

1. The initial tension is too small. The place where the production line leaves the drum is not tight enough, resulting in a decrease in the production line. This situation usually occurs at startup. The solution is to adjust the tensioning device and increase the initial tension.

2、传动滚筒与生产线摩擦不足，导致下降。大多数人不喜欢的原因，是因为涂装设备流水线有水或环境潮湿。解决方法是在滚筒内加入一些松香粉。但要注意不要用手加入，而是用鼓风机设备吹入，以免发生人身事故。

2. Insufficient friction between the transmission drum and the production line leads to a decrease. The reason why most people don't like it is because the painting equipment assembly line has water or the environment is humid. The solution is to add some rosin powder to the drum. But be careful not to add it by hand, but use a blower device to blow it in to avoid personal accidents.

3、后滚子轴承损坏不转动或上下滚子轴承损坏不转动过多。损坏是由过多的尾部漂浮和下沉造成的。损坏或不灵活的零件没有及时修理和更换，增加了阻力并造成打滑。

3. The rear roller bearing is damaged and does not rotate, or the upper and lower roller bearings are damaged and do not rotate too much. The damage is caused by excessive tail floating and sinking. Damaged or inflexible parts are not repaired and replaced in a timely manner, which increases resistance and causes slipping.

4、启动速度过快，会造成打滑。这个时候可以慢慢开始。如果使用鼠笼式电机，可以在点动两次后重新启动，也可以有效克服打滑现象。

4. Starting too fast can cause slipping. At this point, you can start slowly. If a squirrel cage motor is used, it can be restarted after jogging twice and effectively overcome slipping.

5、生产涂装设备流水线负载过大，超过电机容量会导致电机容量下降。此时下降的好处是保护功能不受电机的影响，否则电机用久了会烧坏。但对于手术来说，却是一次滑倒事故。要克服流水线和生产中的滑坡现象，要找到滑坡的原因，然后采取有效措施。

5. Excessive load on the production painting equipment assembly line, exceeding the motor capacity, will lead to a decrease in motor capacity. The advantage of lowering at this time is that the protection function is not affected by the motor, otherwise the motor will burn out if used for a long time. But for the surgery, it was a slip accident. To overcome the phenomenon of landslides in assembly lines and production, it is necessary to identify the cause of the landslide and take effective measures.

上一篇：集中除尘设备的除尘系统特点介绍
下一篇：机器人涂装线的工艺及特点介绍